Whether you’re moving or replacing your current bed with something new, disassembling a sleigh bed can be a little troublesome, especially if you’re not the one who assembled it in the first place. Your manual may be of the best help, but since you’re reading this, you’re looking for the simplest step-by-step guide on how to disassemble a sleigh bed. Read on.
How to Disassemble A Sleigh Bed
Strip Your Bed
This is a pretty obvious step on how to disassemble a sleigh bed; you do not want to start working with all your bed sheets, pillows, mattresses, and everything else. Just strip it off until you see only the frame and the slats. Now, to make things easier for you, you might want to fold the sheets and store them in sturdy containers or boxes so that it would be easier for you to store them after deconstructing the bed and avoiding damage the process.
Detach the Slats or Metal Rails.
Remove the slats across the frame. If you have screwed the slats on the holes at the side rails, make sure to unscrew them. To save yourself from finding missing screws once you reassemble the bed, you should place the screws on containers with caps or place them on the sticky side of at least a 2-inch wide tape to make sure that you have them all. You can mark them, the screws and the holes if the screws and the holes vary in sizes, but if they happen to be in uniform size, you can skip the labeling part.
Detach the Side Rails of the Footboard and Headboard
Using a screwdriver, you need to untighten and remove the screws of the side rails to remove the footboard and the side rails to remove the headboard. To avoid confusion again during reassembly, you might want to label the railings and the boards accordingly. Most how to disassemble a sleigh bed instructional material would include this, despite it being a bit of obsessive-compulsive behavior, this is to help you organize things to avoid confusion in the future.
Remove the Brackets on the Headboard and the Footboard
If your bed doesn’t have brackets installed, then you can skip this step. The brackets attached to the bottom inside of the footboard and the headboard are used to attach the rails that run the length of the bed. Unscrew them from the headboard and footboard. As for the screws, you know what to do with them. If not, you can re-read number 2, and you will know how to save yourself from getting frustrated by finding a lost screw.
Line Up All the Pieces
Some might find this funny, and some might even raise an eyebrow and say that this shouldn’t be included as one of the instructions on how to disassemble a sleigh bed as it is quite obvious, but for those who are not as organized as you might find this very handy.
Remember, while assembling your bed? It was easier to work knowing that every part, screw, bracket, and railing of the bed in reach during the process to anticipate your time of work and to know the size of your work – to see if you need help or you can do it on your own.
Now, that you have disassembled everything, for whatever reasons you have, lining every dissembled piece of your bed after work will allow you to do inventory if nothing is missing. Doing this will allow you to put it in boxes or storage and to avoid worrying about where to find what in the future. Get more tips on sleigh beds.
Conclusion
If you’re more of a DIY guy, disassembling may not be a complex activity for you. But, for those who are going to do it the first time, or those who are not used doing this stuff, deconstructing your bed might be a little tiresome as it is troublesome. Both assembling and disassembling are ideal for a two-person work, especially when you need someone to hold the railings and the board while you’re trying to make sure that your bed is even when you’re done.
You can follow this step-by-step guide on how to disassemble a sleigh bed, and you will be good to go. Just a few reminders though, you might want to clear out your room with things that might complicate your work. You should also prepare everything you need before you start doing the work to avoid standing up and getting something in between works to avoid misplacement and confusion. I hope this will help. Good luck!