Some people know how to remove the bathroom cabinet correctly, but not everyone can do it without ripping the entire wall. It’s easy to remove the bathroom cabinet without leaving a gaping hole in the wall, and I will show you how.
To do so, you’ll need to detach all mounting screws and cut a line through the caulking that connects backsplash. If performed correctly, you may have done half of the work because the trouble begins at removing the backsplash. Not to fret, I have a simple trick to help you get rid of your backsplash and vanity without tearing off the wall.
Tips Before Removing Bathroom Cabinet
Start by switching off the cold and hot water shut-off valves located under the sink. You can then disconnect all the plumbing that is under your sink.
Slit a razor blade between the top of the backsplash and the wall with caulking. Do likewise for side splash.
The backsplash is kept in position with adhesive to caulk and contract. When cutting certain bits, you have to be very careful. What you should do is use a pry bar to clean the backsplash from the ground. Be mindful not to drag so hard that the backsplash breaks off. Position a soft cloth at the backsplash tip to keep the edges from chipping.
Without placing a hole in the ground, the trick to cutting backsplash is to use a 2×4. Place a wooden 2×4 between the wall and the pry bar. It can spread across a larger surface region to prevent the pry bar from punching holes in the wall.
For the stubborn backsplash, I would consider having an even bigger piece of wood; in such cases, a 2×6 or a 2×8 will fit well. Such bigger boards spread the impact over a much broader region, and your bathroom will avoid damaging drywall.
Carefully follow the steps on how to remove the bathroom cabinet to prevent further damage to your water line.
How to Remove Bathroom Cabinet
- Drill with bits
- 2×4 feet wood
- Crescent wrench
- Pipe wrench
- Reciprocating saw
Instruction on How to Remove Bathroom Cabinet
Turn Off the Water. Check underneath the sink, and find the valves for the bath. Until you get to work, it is necessary to shut off the water supply. If the water valves under your sink can not be located, opt to shut down the supply at the main valve. You have to reduce the strain left in the lines by flipping the faucet on. When water no longer works from the tap, then you are ready to launch your project.
Loosen the P-Strap and Disconnect the Water Lines. You may want a handy bucket when performing this move since water can still be left in the P-strap or row. Start by loosening the slip nut, and eliminate the trap if required. Then either remove the lines by hand or use a wrench.
Free the Sink Top From the Wall. You should free the sink top before you uninstall your bath cabinets or vanity. Begin by either cutting the adhesive along the board. Then take the top of the sink off the wall to release it.
Remove the Sink From Bathroom Cabinet. Now that the top of the washbasin is free from the surface, you can completely remove this from the vanity. Depending on how you assembled the sink top would influence how you execute this move. If your sink top is screwed on, just screw out some locked places. If your sink top has been glued, use a chisel and a hammer to remove it.
Remove the Bathroom From the Wall. Taking away the desk from the wall might sound like the hardest aspect of this project, but it’s straightforward. Only slide the screws out of your bathroom cabinet base and bring the vanity away. It should come out of the wall quickly.
Dispose of the Old Cabinet and Clean Up the Bathroom. Consider out the regulation on waste in your city so you can discard your old vanity cabinet properly. Many communities have approved curbside recycling areas with a system than the usual trash collection. Your city can allow you to arrange a “Pay for Pickup” and include a collection charge in case of huge vanities need to pick up. You may want to thoroughly clean up the area after your old vanity is rid of and take care of any required precautions before adding your new bathroom cabinet.
Tips for Removing Bathroom Cabinet
- When assembling, remove the doors and drawers from the vanity. It will minimize the chance that the doors or drawers would be broken as you mount the device.
- The easiest way to remove the excess from the shims is to use a handy knife to mark them. Then flip it down and up to break it. It will provide a smooth transition so that the use of a hammer and chisel will not cause you to worry about ruining the cabinets.
- Please check the place where you would like to mount the vanity before you purchase one. With the old vanity gone, the outlines of the new vanity may also be traced out on the wall with a pencil. This will mean you have ample space and the correct bathroom package.
- Look out for photos while eliminating old vanity. If you don’t get your clips off quickly, tear them off but be vigilant not to damage the toilet wall. The sink is much simpler to attach and remember to clean the broken bits on the floor.
A set of mounting screws are the only items securing your vanity into the board. Now that you know how to remove the bathroom cabinet, scraping the backsplash will be the toughest task. Removing your vanity without leaving a gaping hole to the wall is more than possible; you need to be patient and take the time to remove any adhesive or screws that might secure your bathroom cabinet. Get more tips on cabinets.